Cellulose Nanocrystals Suspensions Research Articles

Chiral nematic nanocomposites with pitch gradient elaborated by filtration and ultraviolet curing of cellulose nanocrystal suspensions

An innovative method combining frontal filtration with ultraviolet (UV) curing has been implemented to design cellulosic nanocomposite films with controlled anisotropic textures from nanometric to micrometric length scales. Namely, an aqueous suspension containing poly (ethylene glycol) diacrylate polymer (PEGDA) as a photocurable polymer and cellulose nanocrystals (CNCs) at a 70/30 mass ratio was processed by frontal filtration, followed by in-situ UV-curing in a dedicated cell. This procedure allowed designing nanocomposite films with highly oriented and densely-packed CNCs, homogeneously distributed in a PEGDA matrix over a thickness of ca. 500 μm. The nanocomposite films were investigated with small-angle X-ray scattering (SAXS), by raster-scanning along their height with a 25 μm vertically-collimated X-ray beam. The CNCs exhibited a high degree of orientation, with their director aligned parallel to the membrane surface, combined with an increase in the degree of alignment as concentration increased towards the membrane surface. Scanning electron microscopy images of fractured films showed the presence of regularly spaced bands lying perpendicular to the applied transmembrane pressure, highlighting the presence of a chiral nematic (cholesteric) organization of the CNCs with a pitch gradient that increased from the membrane surface to the bulk.

Flexible multiple-stimulus-responsive photonic films based on layer-by-layer assembly of cellulose nanocrystals and deep eutectic solvents

Photonic crystal materials responding to environmental stimuli are important in sensors, intelligent detection, and anti-counterfeiting. However, traditional photonic materials usually lack tunable color and sufficient color suppleness, hindering their practical applications. Here, we report a facile strategy to achieve mechanical and color-tunable photonic films by doping deep eutectic solvents (DES) into cellulose nanocrystals (CNC) using layer-by-layer assembly. The amount of DES and several assembly layers were vital in determining the structure color and mechanical and response properties in the CNC photonic films. The experimental results revealed that DES could endow CNC suspension systems with high zeta potential, high viscoelasticity, and low transmittance. The tiny DES compensated for the insufficient flexibility of the CNC film, resulting in a wide color range, high solvent discrimination ability, and multi-color at several view angles. Moreover, photonic crystal film also played an important role in intelligent display and could be applied to traffic reflective signs to remind pedestrians and drivers of road safety and as smart labels for indoor humidity detection. These characteristics of the CNC photonic films could provide a promising strategy for developing advanced intelligent sensors, detection, and anti-counterfeiting materials.

Recent Progress on Photonic Cellulose Nanocrystal Films for Sensing Applications

Abstract: Cellulose nanocrystals (CNCs) have triggered considerable research interest in the last few years owing to their unique optical, biodegradation, and mechanical behavior. Herein, recent progress on the sensing application of photonic CNC films is summarized and discussed based on the analyses of the latest studies. We briefly introduce the three approaches for pre-paring CNCs: mechanical treatment, acid hydrolysis, and enzymatic hydrolysis, recapitulating their differences in preparation and properties. Then, when the aqueous suspension of cellu-lose nanocrystals (CNCs) reaches a specific concentration, it will self-assemble to form a left-handed nematic liquid crystal structure, and this structure can be maintained in films after water evaporation, which has strong photonic crystal properties. The periodic layered structure in the film interferes and diffracts with light, showing a rainbow color. Photonic CNC com-posites that combine CNCs and functional materials have good properties and broad prospects. Finally, we highlight the advanced applications of photonic CNC films, including mechanical sensing, thermal sensing, and humidity sensing. The prospects and ongoing challenges of pho-tonic CNC films were summarized.

Effects of different salt ions on the structure and rheological behavior of sulfated cellulose nanocrystal hydrogel

Cellulose nanocrystal (CNC) hydrogels are increasingly used in various applications. Here, CNC hydrogels were formed by adding four salt ions (NaCl, KCl, MgCl2, and CaCl2) to sulfated CNC suspensions. NaCl and KCl are monovalent salt ions and MgCl2 and CaCl2 are divalent salt ions; each pair has similar cation charges but different cation radii. This study compared the effects of four salt ions on the structure and rheological behavior of CNC hydrogels. At the same ion concentration, compared with NaCl and KCl, the addition of MgCl2 and CaCl2 significantly reduced the distance between the CNC particles, forming pronounced aggregates and denser network structures. Furthermore, the G′ and G″ of the CNC hydrogels with salt ions followed the order NaCl < KCl < MgCl2 < CaCl2 in the small-amplitude oscillatory shear (SAOS) test, and more viscoelastic hydrogels exhibited relatively lower deformability in the creep-recovery test. Under large-amplitude oscillatory shear (LAOS) conditions, the CNC hydrogels with salt ions exhibited LAOS type III behavior, and the change in yield stress followed the same order as the SAOS results. Among them, CNC hydrogel with CaCl2 exhibited stronger nonlinear response and enhanced strain-stiffening behavior (higher I3/I1 and e3/e1) to resist deformation before 20% strain, as well as an enhanced softening effect (higher |v3/v1|) as the structure was destroyed and rearranged at strains ranging from 20% to 100%. Such CNC hydrogels with different salt ions, which can regulate structural and rheological properties, provide basis for designing hydrogels and meet potential requirements in food and biomedicine fields.

Orthotropic organization of a cellulose nanocrystal suspension realized via the combined action of frontal ultrafiltration and ultrasound as revealed by in situ SAXS

HypothesisRodlike cellulose nanocrystals (CNCs) exhibit significant potential as building blocks for creating uniform, sustainable materials. However, a critical hurdle lies in the need to enhance existing or devise novel processing that provides improved control over the alignment and arrangement of CNCs across a wide spatial range. Specifically, the challenge is to achieve orthotropic organization in a single-step processing, which entails creating non-uniform CNC orientations to generate spatial variations in anisotropy. ExperimentsA novel processing method combining frontal ultrafiltration (FU) and ultrasound (US) has been developed. A dedicated channel-cell was designed to simultaneously generate (1) a vertical acoustic force thanks to a vibrating blade at the top and (2) a transmembrane pressure force at the bottom. Time-resolved in situ small-angle X-ray scattering permitted to probe the dynamical structural organization/orientation of CNCs during the processing. FindingsFor the first time, a typical three-layer orthotropic structure that resembles the articular cartilage organization was achieved in one step during the FU/US process: a first layer composed of CNCs having their director aligned parallel to the horizontal membrane surface, a second intermediate isotropic layer, and a third layer of CNCs with their director vertically oriented along the direction of US wave propagation direction.

Angle-resolved optical spectroscopy of photonic cellulose nanocrystal films reveals the influence of additives on the mechanism of kinetic arrest.

Cellulose nanocrystals (CNCs) are rod-like nanoparticles whose chiral self-assembly into photonic films has been promoted as a sustainable source of colouration. Upon drying, an aqueous CNC suspension passes through two regimes: first, a liquid phase, where the CNCs self-organise into a cholesteric liquid crystal, followed by a kinetically-arrested phase, where the helicoidal structure compresses upon loss of solvent, resulting in a solid film with vibrant structural colour. The transition between these two regimes plays an important role in the visual appearance of photonic CNC films, but details on when and how kinetic arrest occurs have remained elusive. In this work, we combine angle-resolved optical spectroscopy of photonic films (approx. 100 vol% CNC) with a model for compressed helicoidal structures to retrieve the suspension conditions during kinetic arrest (approx. 10 vol% CNC). This analysis indicates a shift in the mechanism of kinetic arrest from a glass transition at lower ionic strength to gelation at higher ionic strength, explaining the trends in domain size and film colour. In contrast, neutral additives (glucose, poly(ethylene glycol)) appear to primarily reduce the compression upon drying without affecting cholesteric behaviour, as supported by a general analytical model. These findings deepen our understanding of CNC co-assembly with various commonly-used additives, enabling better control over the production of multifunctional structurally coloured materials.

Two-dimensional strain rate imaging study using a polarization camera and birefringent aqueous cellulose nanocrystal suspensions

The birefringence response of aqueous cellulose nanocrystal (CNC) suspensions in a two-dimensional laminar flow is measured and studied. The suspensions have CNC concentrations of 1.0 wt% (weight percentage) and 1.2 wt%. Cellulose nanocrystals are optically anisotropic rod-like particles that align when subjected to local velocity gradients, whereas at rest, they remain randomly orientated by Brownian motion. The alignment causes birefringence, a phenomenon also known as flow-induced birefringence. We study the flow through an additively manufactured flow channel and measure the amount of birefringence as well as the position of the refractive index axes by using polarizers and a polarization camera. With the help of reference data published in a previous study (Lane, Rode, et al., 2022a), strain rates are derived from the birefringence measurements and compared with numerical simulations. Two flow situations are studied, a plane Poiseuille flow and the flow around a cosine-shaped constriction. The experimentally derived shear rates for the plane Poiseuille flow are consistent with theoretical and computational results. The derived strain rates for the flow around the cosine-shaped constriction show an unexpected asymmetric profile, with the strain rates in the contraction zone being larger than in the expansion zone. The averaged orientation of the CNCs in the flow is linked to the position of the refractive index axes. In the contraction zone, the CNCs tend to align parallel to the flow, whereas in the expansion zone, the CNCs tend to align perpendicular to the flow. The results of this study are discussed in the context of previous, similar studies. The asymmetric strain rate profile around the cosine-shaped constriction is thought to originate from history effects, and the alignment of the CNCs is influenced by extensional rates.

Investigating the phase behaviour of binary suspensions of cellulose nanocrystals and montmorillonite with nonlinear rheology, SAXS and polarized optical microscopy

Using microscopy imaging techniques, X-ray scattering, and nonlinear rheological measurements, we have examined microstructural changes, and phase behavior of cellulose nanocrystals (CNC)/montmorillonite (MMT) composite colloidal systems. Fourier-transform (FT) rheology-stress decomposition methods, Lissajous-Bowditch plots, and other techniques are used to both qualitatively and quantitatively determine the various phases that the suspensions exhibit. In the MAOS (medium amplitude oscillatory shear) region, multiple scaling regions, as well as quadratic scaling regions are obtained. The dependence of the normalized third relative intensity (I3/1) values on angular frequency (ω) also provided new insights into how nonlinear parameters depend on the various CNC/MMT phases. These findings allow us to differentiate various phases exhibited by the composite system, including the isotropic, biphasic, and chiral nematic liquid crystalline (LC) phases. The CNC/MMT nanocomposite system exhibits a variety of liquid crystalline phases, which may contribute to improved mechanical properties for the system, including increased mixture strength, stiffness, and toughness because of the particle alignment in the LC phase. Additionally, the field of optics and photonics may find use for this nanocomposite system in the fabrication of sensors, polarizers, and optical films; energy storage applications where the aligned structures facilitate ion transport; and the formulation of paints and coatings where the strain stiffening and shear thinning behavior of the CNC/MMT composite system are critical.

Phase transition and gelation in cellulose nanocrystal-based aqueous suspensions studied by SANS

HypothesisAqueous suspensions of cellulose nanocrystals (CNC) form a re-entrant liquid crystal (LC) phase with increasing salinity. Phase separation occurs in this LC state leading to a biphasic gel with a flow programmable structure that can be used to form anisotropic soft materials. We term this state a Liquid Crystal Hydroglass (LCH). Defining the mechanisms by which the LCH forms requires detailed structural analysis at the mesoscopic length scale. ExperimentsBy utilising Small Angle Neutron Scattering (SANS), we investigated the microstructure transitions in CNC suspensions, with a particular focus on the unique LC re-entrancy and gelation into the biphasic LCH. FindingsScattering from LCH gels comprises contributions from a dispersed liquid state and static heterogeneity, characterised using a Lorentzian-Gaussian model of inhomogeneity. This conceptually supports a gelation mechanism (spinodal decomposition) in CNC suspensions towards a biphasic structure of the LCH. It also demonstrates that, with increasing salinity, the non-monotonic variation in effective volume fraction of CNC rods fundamentally causes the LC re-entrancy. This work provides the first experimental characterisation of the LC-re-entrancy and formation of an anisotropic LCH gel. The proposed mechanism can be extended to understanding the general behaviour of anisotropic colloids.

Cholesteric Spherical Reflectors with Tunable Color from Single-Domain Cellulose Nanocrystal Microshells.

The wavelength- and polarization-selective Bragg reflection of visible light exhibited by films produced by drying cholesteric liquid crystal (CLC) suspensions of cellulose nanocrystals (CNCs) render these biosourced nanoparticles highly potent for many optical applications. While the conventionally produced films are flat, the CLC-derived helical CNC arrangement would acquire new powerful features if given spherical curvature. Drying CNC suspension droplets does not work, because the onset of kinetic arrest in droplets of anisotropic colloids leads to severe buckling and loss of spherical shape. Here, these problems are avoided by confining the CNC suspension in a spherical microshell surrounding an incompressible oil droplet. This prevents buckling, ensures strong helix pitch compression, and produces single-domain cholesteric spherical reflector particles with distinct visible color. Interestingly, the constrained shrinkage leads to spontaneous puncturing, leaving every particle with a single hole through which the inner oil phase can be extracted for recycling. By mixing two different CNC types at varying fractions, the retroreflection color is tuned throughout the visible spectrum. The new approach adds a versatile tool in the quest to utilize bioderived CLCs, enabling spherically curved particles with the same excellent optical quality and smooth surface as previously obtained only in flat films.

Critical-Like Gelation Dynamics in Cellulose Nanocrystal Suspensions.

We use time-resolved mechanical spectroscopy to offer a detailed picture of the gelation dynamics of cellulose nanocrystal (CNC) suspensions following shear cessation in the presence of salt. CNCs are charged, rodlike colloids that self-assemble into various phases, including physical gels serving as soft precursors for biosourced composites. Here, a series of linear viscoelastic spectra acquired across the sol-gel transition of CNC suspensions are rescaled onto two master curves that correspond to a viscoelastic liquid state prior to gelation and to a soft solid state after gelation. These two states are separated by a critical gel point, where all rescaling parameters diverge in an asymmetric fashion yet with exponents that obey hyperscaling relations consistent with previous works on isotropic colloids and polymer gels. Upon varying the salt content, we further show that these critical-like dynamics result in both time-connectivity and time-concentration superposition principles.

Structural Color from Cellulose Nanocrystals or Chitin Nanocrystals: Self-Assembly, Optics, and Applications.

Widespread concerns over the impact of human activity on the environment have resulted in a desire to replace artificial functional materials with naturally derived alternatives. As such, polysaccharides are drawing increasing attention due to offering a renewable, biodegradable, and biocompatible feedstock for functional nanomaterials. In particular, nanocrystals of cellulose and chitin have emerged as versatile and sustainable building blocks for diverse applications, ranging from mechanical reinforcement to structural coloration. Much of this interest arises from the tendency of these colloidally stable nanoparticles to self-organize in water into a lyotropic cholesteric liquid crystal, which can be readily manipulated in terms of its periodicity, structure, and geometry. Importantly, this helicoidal ordering can be retained into the solid-state, offering an accessible route to complex nanostructured films, coatings, and particles. In this review, the process of forming iridescent, structurally colored films from suspensions of cellulose nanocrystals (CNCs) is summarized and the mechanisms underlying the chemical and physical phenomena at each stage in the process explored. Analogy is then drawn with chitin nanocrystals (ChNCs), allowing for key differences to be critically assessed and strategies toward structural coloration to be presented. Importantly, the progress toward translating this technology from academia to industry is summarized, with unresolved scientific and technical questions put forward as challenges to the community.

The effect of shape, polydispersity, charge, and fraction of crystallite bundles on the cholesteric pitch of cellulose nanocrystal suspensions

Using Onsager–Straley’s second-virial theory, we investigate the cholesteric pitch of cellulose nanocrystal (CNC) suspensions. We model the CNCs as hard chiral bundles of microfibrils and examine the effect of the shape of these chiral bundles, characterized by aspect ratio and chirality, on the cholesteric pitch. Additionally, we explore the impact of length polydispersity and surface charge on the cholesteric phase of CNCs. Furthermore, we consider binary mixtures of twisted bundles and achiral primary crystallites to provide a more realistic representation of CNC suspensions. Our findings reveal that the degree of bundle twisting significantly affects the helical twisting of the cholesteric phase. We also observe that the average particle length and length polydispersity have substantial effects on strongly twisted bundles but minimal effects on weakly twisted ones. Finally, our study indicates that as the range of electrostatic interactions increases, the transfer of chirality from the microscopic to macroscopic length scales becomes masked, resulting in an increase in the cholesteric pitch. In the case of binary mixtures, the bundles act as chiral dopants, and an increasing fraction of bundles progressively enhances the helical twisting of the cholesteric phase.

Low-Frequency Ultrasound Effects on Cellulose Nanocrystals for Potential Application in Stabilizing Pickering Emulsions.

Cellulose, in the form of cellulose nanocrystals (CNCs), is a promising biomaterial for stabilizing Pickering emulsions (PEs). PEs are commonly formed using low-frequency ultrasound (LFU) treatment and impact CNC properties. The present study investigated the specific effects of LFU treatment on CNCs' chemical and physical properties. CNCs were characterized using dynamic light scattering, ζ;-potential determination, Fourier transform infrared spectroscopy, X-ray diffraction, and contact angle measurement. CNC suspensions were studied using rheological analysis and static multiple light scattering. LFU treatment broke CNC aggregates and modified the rheological behavior of CNC suspensions but did not affect the CNCs' chemical or crystallographic structures, surface charge, or hydrophilic properties. During the storage of CNC suspensions and PEs, liquid crystal formation was observed with cross-polarized light. Hypotheses related to the impact of liquid crystal CNCs on PE stability were proposed.

Characterization of CNC Nanoparticles Prepared via Ultrasonic-Assisted Spray Drying and Their Application in Composite Films.

The ultrasonic-assisted spray dryer, also known as a nano spray dryer and predominantly used on a lab scale in the pharmaceutical and food industries, enables the production of nanometer-sized particles. In this study, the nano spray dryer was applied to cellulosic materials, such as cellulose nanofibrils (CNFs) and cellulose nanocrystals (CNCs). CNC suspensions were successfully dried, while the CNF suspensions could not be dried, attributable to their longer fibril lengths. The nano spray drying process was performed under different drying conditions, including nebulizer hole sizes, solid concentrations, and gas flow rates. It was confirmed that the individual particle size of nano spray-dried CNCs (nano SDCNCs) decreased as the nebulizer hole sizes and solid contents of the suspensions decreased. The production rate of the nano spray dryer increased with higher solid contents and lower gas flow rates. The resulting nano SDCNCs were added to a polyvinyl alcohol (PVA) matrix as a reinforcing material to evaluate their reinforcement behavior in a plastic matrix using solvent casting. After incorporating the 20 wt.% nano SDCNCs into the PVA matrix, the tensile strength and tensile modulus elasticity of the neat PVA nanocomposite film increased by 22% and 32%, respectively, while preserving the transparency of the films.

Rheology of cellulose nanocrystal and nanofibril suspensions

Nanocellulose is a sustainable nanomaterial and a versatile green platform that has attracted increasing attention. Although the wide applications of its aqueous suspensions are closely related to rheology, comprehensive studies of their rheological behavior, especially the yielding behavior, are still limited. Herein, to investigate the relationship between structure and rheological properties, the viscoelasticity, thixotropy and yielding behavior of two commonly used nanocelluloses, rod-shaped cellulose nanocrystals (CNCs) and filamentous cellulose nanofibrils (CNFs), were systematically investigated. The viscosity, viscoelasticity and thixotropic behavior of the suspensions were analyzed by steady-state shear, frequency sweep, creep-recovery, hysteresis loop, and three-interval thixotropic recovery tests. The yielding behaviors were evaluated through creep, steady-state shear, step shear rate, stress ramps, amplitude sweep, and large amplitude oscillatory shear tests. The rheological properties of the two typical suspensions showed a strong dependence on concentration and time. However, compared to CNC suspensions, CNF suspensions exhibited stronger thixotropy and higher yield stress due to the higher aspect ratio of CNF and the stronger structural skeleton of the suspensions as supported by Simha's equation and micromorphology analysis. This work provides a theoretical rheology basis for the practical applications of nanocellulose suspensions in various fields.

Tannic Acid-Induced Gelation of Aqueous Suspensions of Cellulose Nanocrystals.

Nanocellulose hydrogels are a crucial category of soft biomaterials with versatile applications in tissue engineering, artificial extracellular matrices, and drug-delivery systems. In the present work, a simple and novel method, involving the self-assembly of cellulose nanocrystals (CNCs) induced by tannic acid (TA), was developed to construct a stable hydrogel (SH-CNC/TA) with oriented porous network structures. The gelation process is driven by the H-bonding interaction between the hydroxyl groups of CNCs and the catechol groups of TA, as substantiated by the atoms in molecules topology analysis and FTIR spectra. Interestingly, the assembled hydrogels exhibited a tunable hierarchical porous structure and mechanical moduli by varying the mass ratio of CNCs to TA. Furthermore, these hydrogels also demonstrate rapid self-healing ability due to the dynamic nature of the H-bond. Additionally, the structural stability of the SH-CNC/TA hydrogel could be further enhanced and adjusted by introducing coordination bonding between metal cations and TA. This H-bonding driven self-assembly method may promote the development of smart cellulose hydrogels with unique microstructures and properties for biomedical and other applications.

Pipe Flow of Suspensions of Cellulose Nanocrystals

The pipeline flow behavior of suspensions of cellulose nanocrystals (CNCs) was investigated over the CNC concentration range of 0.24 to 3.65 wt% in different diameter pipelines. The CNC suspensions were Newtonian below the CNC concentration of 1 wt%. At higher concentrations, the CNC suspensions were non-Newtonian power-law fluids. For Newtonian CNC suspensions, the experimental friction factor–Reynolds number data were obtained only in the turbulent regime, and the data followed the Blasius equation closely. For power-law CNC suspensions, the experimental data of friction factor–Reynolds number covered both laminar and turbulent regimes. The experimental data followed the friction factor–Reynolds number relationships for power-law fluids reasonably well.

Hydrophobic enzymatic cellulose nanocrystals via a novel, one-pot green method

Cellulose nanocrystals (CNCs) are a rapidly growing bionanomaterial with remarkable properties that have been harnessed in various applications, including mechanical reinforcement, biomedical materials, and coatings. However, for non-water-based applications, hydrophobization of CNCs while preserving their integrity is crucial. In this study, we propose a new eco-friendly, one-pot surface esterification method for hydrophobizing enzymatic CNCs in aqueous suspension without solvent exchange. By establishing an appropriate set of reaction conditions, it was possible to create a miscibility gradient that enabled a low-cost, and renewable fatty acid to be utilized as an acyl donor and solvent, allowing direct hydrophobic modification of the as-produced aqueous suspension of enzymatic CNC. FT-IR and AFM-IR analyses confirmed the formation of ester groups, while 13C NMR confirmed the emergence of carboxyl groups. XPS revealed a high degree of surface substitution (0.39) in the modified CNC, while a substantial increase in contact angle (from 40 to approximately 90°) quantitatively confirmed the high efficiency of the enzymatic CNC's hydrophobic modification. Additionally, important properties such as morphology remained practically unchanged, except for a slight increase in thermal stability and crystallinity of the CNCs. Therefore, hydrophobic enzymatic CNCs were successfully produced via a simple, scalable, and environmentally friendly approach without compromising their properties. These hydrophobic CNCs have the potential to enhance nanocomposite compatibility, improve packaging performance for electronics and foods, optimize adhesion in coatings, and offer advancements in cosmetics and drug delivery. However, comprehensive studies are needed to confirm their applicability across these sectors.

Uniaxial orientation of cellulose nanocrystals by zone-casting technique

Cellulose nanocrystals (CNCs) are biomass-based nanoparticles with attractive properties. Using a zone-casting technique, transparent films 2 cm wide and 4 cm long, and 2 µm thick, with uniaxially oriented CNCs were prepared from aqueous suspension of CNCs. The nanocrystals were aligned within the entire film perpendicular to the zone-casting direction. The orientation of the CNCs was confirmed by polarized light microscopy, X-ray diffraction and atomic force microscopy. The intensity of the light transmitted through the films depended on its polarization direction and was the strongest for the light polarized perpendicularly to the crystal orientation direction. The orientation of CNCs in the films resulting in optical anisotropy makes them promising materials for applications in optoelectronics.